Details
DIY 1400KG SINGLE AXLE BOAT TRAILER KIT
HYDRAULIC DISC
45MM SQUARE SOLID STUB AXLES MACHINED TO SLEEVE INTO50X50X5MM R.H.S BOX SECTION
STUD PATTERNS AVAILABLE
FORD (5/114.3 PCD, 1/2" STUDS AND NUTS)
COMMODORE (5/120 PCD, 7/16" STUDS AND NUTS)
HQ (5/120.65 PCD, 7/16" STUDS AND NUTS)
HT (5/108 PCD, 7/16" STUDS AND NUTS)
6 STUD L/C (6/139.7 PCD, 1/2" STUDS AND NUTS) + $120
5 STUD L/C (5/150 PCD, 9/16" STUDS AND NUTS) +$120
IN THIS KIT
X2 45MM SQUARE SOLID STUB AXLES MACHINED TO SLEEVE INTO 50X50X5MM R.H.S BOX SECTION. DISC MOUNTS ARE PRE WELDED FOR CONVENIENCE
2X GALVANISED DACROMET 10" BRAKE DISCS
2X GALVANISED HYDRAULIC DISC CALIPERS WITH STAINLESS STEEL PISTONS.
4 X CALIPER BRAKE PADS
2X S/L BEARING KITS INCLUDING SEALS AND CAPS (MARINE SEALS)
ALL WHEEL NUTS TO SUIT STUD PATTERN PROVIDED
2X 9 LEAF GALVANISED DACROMET SLIPPER SPRINGS. RATED 1600KG PER PAIR (springs are shot peened for extra strength)
2X FRONT SLIPPER HANGERS
2X REAR SLIPPER HANGERS
2X STAINLESS STEEL SLIPPER HANGER BOLTS WITH NUTS AND WASHERS
2X GALVANISED FISH PLATES
4X GALVANISED 50mm x 150mm 1/2" U BOLTS WITH WASHERS AND NUTS
2X GALVANISED AXLE PADS
1X 2000KG GALVANISED 4 HOLE OVERRIDE 50MM BALL COUPLING
1X 3/4"MASTER CYLINDER WITH STAINLESS STEEL MOUNTING BOLTS
1X GALVANISED MASTER CYLINDER BRACKET
4X HIGH TENSILE COUPLING BOLTS WITH NYLOC NUTS
1X 4 HOLE COUPLING WELD ON PLATE
1X 2500MM COUPLING TO AXLE MAIN FLARED BUNDY LINE WITH NUTS (LET US KNOW IF LONGER IS REQUIRED)
1X 1500MM FLARED BUNDY LINE WITH NUTS
1X 500MM FLARED BUNDY LINE WITH NUTS
1X 400MM MALE / FEMALE FLEXI LINE
1X BRASS T PIECE
1X MASTER CYLINDER NUT AND WASHER
ALL COPPER FITTINGS AND T PIECES TO COMPLETE AXLE AND FINISH OFF AT COUPLING WITH PRE FLARED LINES!!
Please check coupling to axle hydraulic line length. if longer is required please get in contact with us
On ordering please provide your stud pattern?
upgrade to the easy instillation hydraulic line setup.
12ft set up: $70 (CLICK ON LINK BELOW)
16ft set up: $75 (CLICK ON LINK BELOW)
"UPGRADE TO 12FT FULL FLEXI KIT BY CLICKING HERE"
"UPGRADE TO 16FT FULL FLEXI KIT BY CLICKING HERE"
EXTRAS AVAILABLE
UPGRADE TO JAPANESE BEARINGS $50.0 (CLICK ON LINK BELOW)
"CLICK HERE TO UPGRADE TO JAPANESE MANUFACTURED BEARINGS"
SHOT PEENING
Shot peening is a cold working process used to produce a compressive residual stress layer and modify mechanical properties of metals and composites. It entails impacting a surface with shot with force sufficient to create plastic deformation. Shot peening is often called for in aircraft repairs to relieve tensile stresses built up in the grinding process and replace them with beneficial compressive stresses.
DACROMET®
DACROMET®, is the leading inorganic coating commonly specified in the wind turbine, heavy truck, marine, agricultural, construction equipment and aerospace industries. A water-based, VOC-compliant coating, DACROMET® is comprised mainly of overlapping zinc and aluminum flake in an inorganic binder.